This subnet is reached through the firewall 10. I am not a network expert, but as far as I know, when a packet can't reach its destination, ip stack doesn't try an other route. Core Switch static Routing table Gateway of last resort is 10. I don't currently have anything like this for my E73. But the output that you post does not show any messages about expired in transit. And is not visable in show config And as far as i know this did not set back when the switch qas defaulted.
You have to use an snmp tool to reset the value. Thanks, Resolut1on Did you Enable the Ip forwarding Globally? It should have been dropped at the edge of your home network. I will look for the doc on that and share. I had this with a used switch once, eveything looked on except the ttl was reduced to far. If we has all output from show config we could see that If you can not find any other culperate. The basic reason to get this message is the Time To Live value set for a packet reduced to zero while traveling through a network.
The comments under that question has the info i used to determine if this is the issue. I have problem with Inter-Vlan. Destination host unreachable This determines if the destination node is down or is not operating on the network. Recently, during the problem occured, i have added 172. It also includes traceroute and telnet, but I haven't tested the latter yet. Your output does show what appears to be a small loop between 10. Maybe through a login or a certificate? I had this with a used switch once, eveything looked on except the ttl was reduced to far.
The Default Gateway must shows 192. Me - I can't answer at this moment, i'll be back for this. I have several of these remote sites set up so far but this one is puzzling me. Hi Paul, I disabled my wireless connection now. Hard to come up with an answer. But you say other people can get replies when they ping you. You can see the packet start at 10.
Does the swith pass traffic in 1 vlan? Eric - An other thing that is comming straight from windows world : 2 or more default gateway. Hey guys, im hoping someone can help me in here. Hi techies, I tried to do a ping on one of the sites hosted at one of the servers in another network. Router A thinks the best path is thru router B. It also determines the network accessibility of a specific and is used in order to determine and ensure that a computer which a user is trying to reach is really operating.
Below are the steps of what usually happens when a user pings a machine. Is it possible that some link is flapping like that? If the host is available, it responds with a single packet. Last question today : do you have vLan in your network? Me - Actually before this we only using 1 gateway ip which is 172. So they play ping-pong with the packet. But for me, that's one more stone turned. Ive tried everything from disabling the firewall on the router and even my software firewall, and it still doesnt help.
Back on the x450 g1 the ttl can be changed in switch via snmp command. Thanks for clarifying the route for 172. I have no idea why the server should go through the default gateway 172. Does that mean the signal is being blocked by his end somewhere? The message sent to the host is a Packet Expired in Transit message. All I have is the firewall on the router and the windows firewall, but i even tried turning that off. I have a specific subnet 172.
However due to misconfiguration, 5. It is because of avoiding any chance of infinite looping of packets. This may occur because of the non-existence of a local or remote route for the destination host. If not, then you have no Internet connection. Well, endlessly is not quite correct. Basically the error means that something happened to the ping packet and it wasn't able to find its destination in time which is indicative of a network issue.
I will look for the doc on that and share. The cause may be from a short circuit, due to flooding or water ingress? I will look for the doc on that and share. Inter-vlan routing not working Does the swith pass traffic in 1 vlan? This issue can be corrected by adjusting the route on Router3 to send data destined for the 192. If you are not able to ping the Gateway switch off the Window firewall and try once. I might cut the part which shows that. Mike Muus coined this tool name from the sound that the sonar makes because its methodology is similar to the echolocation of sonar. Back on the x450 g1 the ttl can be changed in switch via snmp command.